Admission Prices

Adults: $10
Seniors: $7
Students (12-15 yrs): $7
Children (6-11 yrs): $2
Pit pass: $30 - Driver; $30 - Crew

Admission prices for special events may be different than listed above.

 

Limited Modified

2013 Rules, Regulations, & Car Specifications

 

CAR & BODY:

Limited Modified

2013 Rules, Regulations, & Car Specifications

1. 108 wheel base minimum. 2350 pounds minimum. All car bodies must look like a normal modified; must be track approved before racing.

2. Roof rear sail panels are allowed one 90 degree bend along the top edge of the sail panel, but must be less than 1” wide. Gremlin style roofs not allowed.

3. No more than 6” of total rake allowed on the body deck. A maximum of 3” of rake (of the 6” total) is allowed in the door section and a maximum of 3” of rake is allowed in the quarter panel section.

4. Minimum ride height is 5” from ground to side frame rails.

5. Plastic body panels and plastic filler are not allowed.

6. No convertibles.

7. Car must have full deck interior from one side of the body to the other. Decks must be

aluminum or sheet metal.

8. Minimum of three (3) windshield bars 5/16” in diameter is required. Must be mounted in

front of driver.

9. One single nerf bar between the front and rear wheels, on each side of the car is allowed.

Maximum size = 1 1⁄2 x .095. They are to be attached to the cage at the front and rear sections of the nerf bar. No center supports are allowed on the nerf bar. Nerf bars may not be outside of tires. All bumper and nerf bars must be capped.

10. Oil and transmission fluid coolers are not allowed in driver’s compartment.

11. No upholstery allowed, other than driver’s seat cover.

12. No plastic in driver’s compartment.

13. Hood scoops optional.

FENDERS:

Quarter panels must be 90 degrees to the ground, with a maximum of a 45 degree bend 4” from the bottom of the doors and quarters and 2” on top.

FIREWALL:

Must be metal or aluminum with minimum sized holes for throttle, etc. Firewall must be sealed from engine compartment.

FLOOR:

Must be metal or aluminum. Must cover entire driver cockpit to front edge of seat.

HOOD:

1. Must cover completely the top of engine and radiator.

2. Must extend from the nose piece to the deck.

3. Hood must be made of metal, aluminum, or fiberglass.

4. Hood must provide a seal to the top of the engine compartment.

5. Cannot cover side of engine more than 5”.

6. Hood scoops okay.

SPOILER:

Rear spoiler optional. Rear spoiler may be 8” x 60”, spoiler side boards - 8” to taper to 1” point length 12” base.

FRAME:

1. Frame cannot be cut, bent, or altered to change suspension brackets, except upper control arm brackets on front end.

2. Front frame horns can be cut off in front of the steering box and idler arm.

3. May use a normal modified frame. No pull or push bars.

4. Replacement may be made with round, square, or rectangular tubing.

5. Front frame may be cut for radiator clearance.

6. Frame may be cut for seat clearance.

7. You cannot cut holes in frame to lighten it. Rust may be removed in front of lower rear

trailing arms and cleaned up on body mount holes.

8. Cross member mounts on frame for transmission may be removed, but cannot be farther

forward than welds on frame.

9. If weights are used for ballast, weights must be painted white and number of car must be

on weight. No mercury ballast or any similar type of ballast may be used. All weight must be securely fastened. Loss of weight will be cause for disqualification.

E-Modified Rules Page 2

ralogo
wreckerlogo2
wreckerlogo
home40161
home40091
home40071
home40061
home40041
home40081
item7
home40051
home40021
home40031
home40001
 Copyright  2012 Brill's Motor
BMSBanner3


Gates Open:
4:30 p.m.

Hot laps: 7 p.m.

Races Start: 7:30 p.m.